Ryobi Feeder Board

THE HIGHEST QUALITY ROLLERS • THE BEST CUSTOMER SERVICE • ECONOMICAL PRICING

HOME

ROLLERS

ROLLER KITS - 20% OFF

TheRollerStore

803 Randolph St

Valdosta, GA 31602

229.241.8022

229.241.8023 fax

Sales Policy

229.241.8023 (fax)

RYOBI 3302 FEEDER BOARD VIEW DIAGRAM
DESCRIPTION	COMMENTS, SEC 355	RYOBI #
BEARING FOR LOWER FEEDER BOARD BELT ROLLER	When replacing feeder board belts it's advisable to replace the lower belt roller bearings at the same time, as they are highly loaded and prone to failure (The upper belt roller bearings are larger and do not have the same tendency to fail)	530090200
BELT GUIDE DETENT SPRING	SN: 7037 AND up (4 BELTS), Flat spring, fits inside of the belt guide, bears against the belt guide shaft to maintain the position of the belt guide on the shaft	534035535
BELT GUIDE DETENT SPRING	SN: 7036 AND BELOW (7 OR 5 BELTS), Flat spring, fits inside of the belt guide, bears against the belt guide shaft to maintain the position of the belt guide on the shaft	5300591261
BELT GUIDE	SN: 7036 AND BELOW (7 OR 5 BELTS), Moveable guide, controls the lateral position of the feed table belt (1 per belt)	534135538
BELT GUIDE	SN: NUMBERS 7037 AND up (4 BELTS), Moveable guide, controls the lateral position of the feed table belt (1 per belt)	5341355381
The ENDLESS tapes differ in the number of belts per set and by serial number. They are NOT interchangeable. To avoid errors, please check the number of belts and verify the serial number.
BELT SET - 7 BELTS	SN: 4432 AND BELOW	534035534
BELT SET - 5 BELTS	SN: 4433 - 7036	5340355342
BELT SET - 4 BELTS	SN: 7037 AND ABOVE	5340355343
CONVEYOR GUIDE EXTENDER KIT		534035950
LOWER FEEDER BOARD TAPE/BELT ROLLER		533035536
PUSH GUIDE CARRIER, NOS	SN: 4433 AND up	5341358511
PUSH GUIDE CARRIER, OS	SN: 4433 AND up	5341357931
PUSH GUIDE SPRING BRACKET COMPLETE ASSY	SN: 4433 AND up, Complete assembly of the push guide spring bracket with a set of springs and the quick fastener which secures it to the push guide on either the OS or NOS side	534035650
PUSH GUIDE SPRING, HEAVY	SN: 4432 AND BELOW, old STYLE feeder board, mounts directly to the NOS guide with size M4 screws	543039416
PUSH GUIDE SPRING, HEAVY	SN: 4433 AND UP, For new STYLE feeder board, mounts to a bracket which can be attached to either the OS or NOS push guides, mounts with size M3 screws	534135882
PUSH GUIDE SPRING, LIGHT	SN: 4432 AND BELOW, old STYLE feeder board, mounts with M4 screws directly to the NOS guide	543039415
PUSH GUIDE SPRING, LIGHT	SN: 4433 AND UP, new STYLE feeder board, mounts with size M3 screws to a bracket which can be attached to either the OS or NOS push guides	534135883
RETAINER TAPE FOR LOWER FEEDER BOARD	LONG, HEAVY WEIGHT, Attaches to the cross shaft midpoint of the feeder board, use with heavier weight stocks	534035556
RETAINER TAPE FOR LOWER FEEDER BOARD	LONG, LIGHT WEIGHT, Attaches to the cross shaft midpoint of the feeder board, use with lighter weight stocks	534035555
RETAINER TAPE FOR LOWER FEEDER BOARD	SHORT, Attaches to the cross shaft midpoint of the feeder board	534035557
RETAINER TAPE FOR UPPER FEEDER BOARD	Attaches to the pullout roller shaft at the top of the feeder board	534035554
SKID ROLLER LARGE	One pair of large skid rollers is positioned directly above the tail of the sheet when the lead edge is against the head stops. A second pair of large skid rollers is positioned midway between the pair at the sheet tail and the small skid rollers which are located above the upper belt roller	533090218
SKID ROLLER LARGE, ASSEMBLY	Complete assembly of the large bearing, shoulder screw, arm & clamp	5430366601
SKID ROLLER SMALL	The small skid rollers are positioned at the entrance to the feeder board, directly above the upper belt roller	533090212
SKID ROLLER SMALL, ASSEMBLY	Complete assembly of the small bearing, shoulder screw, arm & clamp	5430366501

Copyright © 2007-2012 TheRollerStore.com and TheRollerStore.com, Inc. All rights reserved.
Use of this site and its services indicates your acceptance of all Terms and Conditions found in the Web Site Visitor Agreement.

Updated January 22, 2012